Raise boring |
|
Каталог >> Каталог бурового инструмента >> Raise boring |
|
Section content:
Cutters
 |
 |
 |
| RCC11 RCC 11 is a multipurpose cutter and the best choice in certain rock formations or if a small chip is preferred. |
RCC 5 In hard and tough rock formations, a 26 mm spacing is vital to get an efficient kerf breakage. To achieve a 26 mm spacing you should use a combination of RCC 4 and RCC 5 cutters on the reamer. |
RCC 4 The RCC 4 Duro Cutter with a 52 mm spacing gives the largest chips and the fastest penetration in soft and brittle rock. |
RCC Cutters |
Part No. | Insert type | Weight kg |
| RCC 4 RCC 5 RCC11 |
5107-6029-93 5107-6029-92 5107-6029-35 |
Chisel Chisel Chisel |
126 130 135 |
"C" Cutters |
Part No. | Insert type | Weight kg |
| C23 C24 C24 |
5107-6029-97 5107-6025-10 5107-6025-30 |
Chisel Spherical Chisel |
165 143 145 |
SRCC Cutters |
Part No. | Reamer head | Insert type | Weight kg |
| SRCC4 SRCC5 |
5107-6030-06 5107-6030-07 |
Sandvik Reamers Sandvik Reamers |
Chisel Chisel |
121 125 |
Rebuild kit
Rebuild Kit RCC cutters |
Part No. | Rebuild kit components | Seal kit components | Quantity |
| Rebuild Kit, complete Seal Kit, complete Shaft Seal Retainer, R.H. Seal Retainer, L.H. Large Seal Set Bearing Cone Bearing Cup Cup Bearing Spacer Cone Bearing Spacer Plug, .25" NPT Locking Tab O-ring O-ring Small Seal Set Releaf Valve Vent Plug |
5750-0085-57 5107-6036-28 5107-6025-01 5107-6029-91 5107-6029-90 B47037-1 A17000-2 A17000-1 5107-6025-05 5107-6025-06 A23395 5107-6025-07 652-661 652-545 5107-6025-22 A30069-2 A37695-2 |
X X X X* X X X X X X X |
X X X X X X X |
1 1 1 1 1 1 2 2 1 1 3 1 1 1 1 1 1 |
Rebuild Kit SRCC cutters |
Part No. | Rebuild kit components | Seal kit components | Quantity |
| Rebuild Kit, complete Seal Kit, complete Shaft Seal Retainer, R.H. Seal Retainer, L.H. Large Seal Set Bearing Cone Bearing Cup Cone Bearing Spacer Plug, 1/4 NPT Locking Tab O-ring O-ring Small Seal Set Releaf Valve Vent Plug Bearing Set |
5750-0130-24 5107-6036-29 5107-6029-03 5107-6030-13 5107-6033-12 B47037-1 A17000-2 A17000-1 A72677-1 A23395 5107-6029-17 652-661 652-545 5107-6025-22 A30069-2 A37695-2 B69347-4 |
X X X X* X X X X X X X X |
X X X X X X X |
1 1 1 1 1 1 1 1 1 3 1 1 1 1 1 1 1 |
Tool Kit for rebuilding |
Part No. | Quantity |
| Tools for cutter rebuilding | 5107-6036-11 | 1 |
Saddles, Stingers
Standard saddles for RCC cutters |
Part No. |
| Bolt-on 0o Weld-on 14o Weld-on 39o | 5750 500149 C37137-3 C37136-4 |
Hardware for saddles |
Part No. |
| Shaft retainer Barrel nut Roll pin 1/2" x 1 1/2" Screw 3/4" x 5 1/2" UNC Screw 1" x 3" UNC Locking washer 3/4" Locking washer 1" |
5107 6035-31 A31345-1 637-274 0144 4001 16 0144 3577 00 A64998-11 A64998-13 |
Bicon design stingers
| Pilot hole diame ter | DI22 CON | Length | Weight | Stinger Part No. wear pads< | Weld on wear pad | |||
| Integral | Carbide insert | Weld on | Part No. | Quantity | ||||
| Capacity: Standard* | ||||||||
| 229 251 279 311 349 | 6 3/4 6 3/4 8 1/4 9 1/4 10 1/2 | 1880 1880 1880 1990 1905 |
570 590 725 910 950 |
D68220-1 D72653-1 5750 5000 18 5750 5002 31 5750 0053 34 |
5750 0112 38 5750 0112 39 5750 0112 40 5750011241 |
5750 0112 28 5750 0112 29 5750 0112 30 5750011231 |
5750 0112 32 5750 0112 33 5750 0112 34 5750 0112 35 |
5 5 6 6 |
| Capacity: Large* | ||||||||
| 311 349 349 381 381 |
9 1/4 10 1/2 10 1/2 11** 11** |
2085 2085 2590 2590 3100 |
1135 1225 1540 1810 2270 |
5750 5010 13 5750 5001 01 5750 0082 93 5750 0063 39 |
5750 0112 44 5750 0112 45 5750011246 5750011247 5750 0100 09 |
5750011242 5750011243 5750 0075 38 |
5750 0112 35 5750 0112 36 5750 0112 37 |
6 6 12 |
